How to Upgrade a 2007 2008 2009 Mercury Mountaineer DVD Player with Aux Input Radio Stereo

135 views

For those who want to upgrade a factory radio for a 2007 2008 2009 Mercury Mountaineer with a new aftermarket stereo, before pick a stereo, you should check the compatibility between your stereo and your car. There are many 2007 2008 2009 Mercury Mountaineer stereo available in the market, only few of them support a wide range of practical and entertainment features. Today I would like to share with you a 2007 2008 2009 Mercury Mountaineer car stereo from Seicane which can meet almost all your needs in car. First of all, here come its installation steps.

2007 2008 2009 Mercury Mountaineer car stereo after installation

2007 2008 2009 Mercury Mountaineer car stereo after installation

Before and during installation, you should notice:

1.Before connecting, please make sure the ignition is off to avoid short circuit.

2.Ensure connect the yellow and red power cable at last.

3.Ensure that all loose wires are isolated with electrical tape

4.Ensure don’t tangle the wire when tighten the moving parts(Such as seat rails).

5.Ensure that all ground is connected to the same place.

6.Using the improper fuse may cause damage of fire, so when replace the fuse, please consult the professional.

7.For your convenience, here’s the recommended tools for removal and installation from Seicane, please check for more details: http://www.seicane.com/car-dvd-dismantling-devicesrd-400

2007 2008 2009 Mercury Mountaineer stereo installation steps

Step 1: Remove the trim around gear shifter.

Remove the trim around gear shifter

Remove the trim around gear shifter

Step 2: Remove screws securing center console lid with a screwdriver.

Remove screws securing center console lid with a screwdriver

Remove screws securing center console lid with a screwdriver

Step 3: Remove the center console trim.

Remove the center console trim

Remove the center console trim

Step 4: Remove console side panels on both driver and passenger sides.

Remove console side panels on both driver and passenger sides

Remove console side panels on both driver and passenger sides

Step 5: Remove bolts securing radio bezel and AC controls.

Remove bolts securing radio bezel and AC controls

Remove bolts securing radio bezel and AC controls

Step 6: Unplug AC controls (from passenger side).

Unplug AC controls (from passenger side)

Unplug AC controls (from passenger side)

Step 7: Remove the radio bezel and AC controls.

Remove the radio bezel and AC controls

Remove the radio bezel and AC controls

Step 8: Remove screws securing radio to the vehicle, and take the original radio out of the dash.

Remove screws securing radio to the vehicle, and take the original radio out of the dash

Remove screws securing radio to the vehicle, and take the original radio out of the dash

Step 9: Check all the accessories for the new Seicane stereo.

Check all the accessories for the new Seicane stereo

Check all the accessories for the new Seicane stereo

Step 10: Connect the harnesses to the back of the new Seicane stereo.

Connect the harnesses to the back of the new Seicane stereo

Connect the harnesses to the back of the new Seicane stereo

Step 11: Connect the Seicane stereo to your original car radio’s plugs, and put the new Seicane stereo into the dash.

Step 12: Turn on the new Seicane stereo and check whether the radio is working properly.

Step 13: Install all screws, trims, panels, bolts and the radio bezel and AC controls into their original place.

 

Above all are the installation steps for a 2007 2008 2009 Mercury Mountaineer DVD Player. If you have any doubts, you can contact with your dealer or seek help from a professional. If you haven’t got a suitable car stereo for your car, you can check the following link which is a 2007 2008 2009 Mercury Mountaineer DVD Player from Seicane.

 

http://www.seicane.com/seicane-pure-android-quad-core-dvd-gps-in-dash-radio-system-for-2007-2008-2009-mercury-mountaineer-with-16g-flash-3g-wifi-bluetooth-mirror-link-obd2-rearview-camera-s127302

This Android 2007 2008 2009 Mercury Mountaineer stereo comes with high configuration including the stable 5.1.1 operation system, Quad-core 1.6 GHz CPU, 16GB Flash, 7 inch high definition capacitive screen with 1024*600 resolution. Based on these improved configurations and performance, this stereo runs faster than the factory one.

This unit upgrades your car with BC6 Bluetooth module for hands-free calls and music streaming.

As long as you wireless connect your Bluetooth-enabled mobile phone with this unit, you can dial, answer, reject and mute calls without taking your hands off the steering wheel. And the capability to stream your favorite tunes from your Smartphone wirelessly is also desirable. Apart from Bluetooth connectivity, there are many other features being supported by this unit, including 3D GPS navigation, DVD player, USB/ SD connection, file management, steering wheel control, etc. With these different features, this stereo can meet your different needs. Wish you like it and good luck to you!

Related Posts

Posted in Uncategorized. Tagged with .

Leave a Reply

Your email address will not be published. Required fields are marked *

You may use these HTML tags and attributes: <a href="" title=""> <abbr title=""> <acronym title=""> <b> <blockquote cite=""> <cite> <code> <del datetime=""> <em> <i> <q cite=""> <strike> <strong>