http://www.carstereofaqs.com/wp-admin/edit.php?post_type=custom-css-js

Monthly Archives: June 2016

How to install a 2001-2011 TOYOTA HILUX car stereo with CD DVD Player Radio GPS Audio System Bluetooth Music Mirror Link OBD2 3G WiFi AUX Android 5.1.1 Touch Screen

If you are going to replace your factory radio, you can find a step-by-step installation instruction to help the installation, which can probably help you save quirt a lot of money if you can install it on your own. Now I’d like to share a professional 2001-2011 TOYOTA HILUX car stereo installation guide from Seicane with you. Wish you can get some help from it.

2001-2011 TOYOTA HILUX car stereo after installation

2001-2011 TOYOTA HILUX car stereo after installation

Before and during installation, you should notice:

1.Before connecting, please make sure the ignition is off to avoid short circuit.

2.Ensure connect the yellow and red power cable at last.

3.Ensure that all loose wires are isolated with electrical tape

4.Ensure don’t tangle the wire when tighten the moving parts(Such as seat rails).

5.Ensure that all ground is connected to the same place.

6.Using the improper fuse may cause damage of fire, so when replace the fuse, please consult the professional.

7. For your convenience, here’s the recommended tools for removal and installation from Seicane, please check for more details: http://www.seicane.com/car-dvd-dismantling-device-srd-400

2001-2011 TOYOTA HILUX car stereo installation guide

1.Remove two trim panels at each side of the center console and set it aside.

Remove two trim panels at each side of the center console and set it aside

Remove two trim panels at each side of the center console and set it aside

2.Remove the top panel and set it aside.

Remove the top panel and set it aside

Remove the top panel and set it aside

3.Remove 4 screws holding the unit with a Phillips screwdriver.

Remove 4 screws holding the unit with a Phillips screwdriver

Remove 4 screws holding the unit with a Phillips screwdriver

4.Gently take out the panel on the radio interface.

Gently take out the panel on the radio interface

Gently take out the panel on the radio interface

5.Take out the radio and disconnect cables at back of it.

Take out the radio and disconnect cables at back of it

Take out the radio and disconnect cables at back of it

6.Check all the accessories for the new Seicane car stereo.

Check all the accessories for the new Seicane head unit

Check all the accessories for the new Seicane head unit

7.Connect the harnesses to the back of the new Seicane car stereo.

Connect the harnesses to the back of the new Seicane head unit

Connect the harnesses to the back of the new Seicane head unit

8.Connect the Seicane car stereo to your original car radio ‘s plugs.

9.Put the new Seicane car stereo into the dash.

10.Turn on the new Seicane car stereo and have a comprehensive check if it works well.

11.Install 4 screws back to their original position.

12.Install the trim panel back to its original place.

Wish you can get some help from the detailed 2001-2011 TOYOTA HILUX car stereo installation guide above. If there is any question, you can consult your dealer. However, if you can’t finish it on your own, you’d better ask a professional for help. If you are still looking for an ideal car stereo for your car, you can refer to this amazing 2001-2011 TOYOTA HILUX car stereo from Seicane. Please click for more details:

http://www.seicane.com/seicane-s126003-cheap-hd-touch-screen-android-2001-2011-toyota-hilux-with-cd-dvd-player-radio-gps-audio-system-bluetooth-music-mirror-link-obd2-3g-wifi-aux-steering-wheel-control

Coming with all the mainstream features you can expect from a top car stereo, this intelligent TOYOTA HILUX car stereo with an accurate GPS navigation system will guide you to your desired destination with the least time. The region free DVD player is able to play a multitude of media files such as DVD/DIVX/MP4/MP3/MP2/VCD will keep you and your passengers entertained on the whole trip. You’ll even be able to manage files of an SD card, your iPod or USB stick! Just have fun and good luck to you!

Posted in Uncategorized.

A detailed installation guide for a 2005-2011 TOYOTA Vitz Echo car stereo with HD Touch Screen Bluetooth Radio WiFi 3G DVR Mirror Link OBD2

As is known, a GPS navigation which can provide the most accurate direction and voice guidance is much helpful for car owners who are going to arrive at the unfamiliar locations. However, not all factory radio comes with GPS navigation function. In that case, you can easily replace your factory radio with a new aftermarket head unit which usually can be compatible with a lot of features. To install it in your car, a detailed installation guide can be instructive. If you are a car owner of a 2005-2011 TOYOTA Vitz Echo, you can take this 2005-2011 TOYOTA Vitz Echo car stereo instruction from Seicane as a reference.

2005-2011 TOYOTA Vitz Echo car stereo after installation

2005-2011 TOYOTA Vitz Echo car stereo after installation

Tips about the installation: 

1.Please disconnect the power before the installation.

2.Please prepare a lever and a screwdriver before the removal and the installation.

3.Please keep all the separate parts from the car. Please take great care of the dashboard to avoid scratching it during its detachment and installation. Please keep handy any parts from the car and make use of all the original screws from the car as much as possible. so each related part of the unit can be fixed securely.

4.For your convenience, here’s the recommended tools for removal and installation from Seicane, please check for more details: http://www.seicane.com/car-dvd-dismantling-device-srd-400

2005-2011 TOYOTA Vitz Echo car stereo installation guide

1.Remove two trim panels at each side of the center console and set it aside.

Remove two trim panels at each side of the center console and set it aside

Remove two trim panels at each side of the center console and set it aside

2.Remove the top panel and set it aside.

Remove the top panel and set it aside

Remove the top panel and set it aside

3.Remove 4 screws holding the unit with a Phillips screwdriver.

Remove 4 screws holding the unit with a Phillips screwdriver

Remove 4 screws holding the unit with a Phillips screwdriver

4.Gently take out the panel on the radio interface.

Gently take out the panel on the radio interface

Gently take out the panel on the radio interface

5.Take out the radio and disconnect cables at back of it.

Take out the radio and disconnect cables at back of it

Take out the radio and disconnect cables at back of it

6.Check all the accessories for the new Seicane car stereo.

Check all the accessories for the new Seicane car radio

Check all the accessories for the new Seicane car radio

7.Connect the harnesses to the back of the new Seicane car stereo.

Connect the harnesses to the back of the new Seicane car radio

Connect the harnesses to the back of the new Seicane car radio

8.Connect the Seicane car stereo to your original car radio ‘s plugs.

9.Put the new Seicane car stereo into the dash.

10.Turn on the new Seicane car stereo and have a comprehensive check if it works well.

11.Install 4 screws back to their original position.

12.Install the trim panel back to its original place.

That’s all the installation instruction for a 2005-2011 TOYOTA Vitz Echo car stereo in particular. If you have any question, you can turn to your dealer for help. If it’s the first time for you to install a new unit in your car, you’d better ask a professional for help.

On the other hand, if you don’t get an ideal head unit, I’d like to recommend an ideal TOYOTA Vitz Echo car stereo from Seicane to you. For more details, you are welcome to check it out with the following link:

http://www.seicane.com/seicane-s126002-android-dvd-player-2005-2011-toyota-vitz-echo-hd-touch-screen-aftermarket-navigation-car-stereo-with-bluetooth-radio-wifi-3g-dvr-mirror-link-obd2-steering-wheel-control

With this TOYOTA Vitz Echo car stereo in your car, you can use GPS function and enjoy DVD, CD, TV plays, dramas, etc. all the way wherever you go. With the advanced BC6 Bluetooth module, you can make hands-free phone calls for a safer driving and play music from your Bluetooth-enabled mobile phone. This unit is guaranteed to bring you both excellent guidance and exciting experience on all trips. Good luck to you!

Posted in Uncategorized.

How to upgrade a 2006-2011 Kia sedona car stereo with Radio GPS Navigation DVD Player Head Unit Touch Screen WiFi 3G Bluetooth Music

Please look at the picture below, are you familiar with it? If you say yes, then you may probably own a 2006-2011 Kia Sedona, it’s actually a picture about a 2006-2011 Kia sedona car stereo after installation. To install such a unit in your car, you can simply ask a professional for help if you don’t have any experience. This article is the detailed 2006-2011 Kia sedona car stereo installation guide from Seicane for your reference.

2006-2011 Kia sedona car stereo after installation

2006-2011 Kia sedona car stereo after installation

Precautions for this installation:

1.Before you start up any work, park your car well and unplug the negative power cable to avoid any danger.

2.Please make sure that all fastened wires are isolated with electrical tape.

3.Please make sure the ignition is off to avoid short circuit.

4.Please prepare a lever and a screwdriver before the removal and the installation.

5.For your convenience, here’s the recommended tools for removal and installation from Seicane, please check for more details: http://www.seicane.com/car-dvd-dismantling-device-srd-400

2006-2011 Kia sedona car stereo installation guide

1. The original car radio.

The original car radio

The original car radio

2. Pry around the edges of the panel with a lever, and then remove the panel with your hands.

Pry around the edges of the panel with a lever, and then remove the panel with your hands

Pry around the edges of the panel with a lever, and then remove the panel with your hands

3. Disconnect all the connectors at the back of the panel.

Disconnect all the connectors at the back of the panel

Disconnect all the connectors at the back of the panel

4. Unscrew four screws holding the original radio in place with a screwdriver.

Unscrew four screws holding the original radio in place with a screwdriver

Unscrew four screws holding the original radio in place with a screwdriver

5. Take the original radio out of the dash.

Take the original radio out of the dash

Take the original radio out of the dash

6. Disconnect the connectors at the back of the original radio.

Disconnect the connectors at the back of the original radio

Disconnect the connectors at the back of the original radio

7. Check all the accessories for the new Seicane car stereo.

Check all the accessories for the new Seicane car radio

Check all the accessories for the new Seicane car radio

8. Connect the harnesses to the back of the new Seicane car stereo.

Connect the harnesses to the back of the new Seicane car radio

Connect the harnesses to the back of the new Seicane car radio

9. Connect the Seicane car stereo to your original car radio’s plugs.

10. Turn on the new Seicane car stereo to have a careful check if everything works well. If it doesn’t, please check whether all the cables are connected correctly.

11. Put the new Seicane car stereo into the dash.

12. Put everything into their original place.

Above all, you need to make clear about every step before you start to install this 2006-2011 Kia sedona car stereo in your car. If there is any question, you can seek help from your dealer. If you don’t have any experience on the installation, it’s strongly suggested you ask a professional to install your new unit. If you are still looking for a suitable head unit for your car, I’d like to recommend a great 2006-2011 Kia sedona car stereo from Seicane to you. Please click for more details:

http://www.seicane.com/seicane-s127678-android-2006-2011-kia-sedona-carnival-radio-gps-navigation-car-stereo-dvd-player-head-unit-touch-screen-bluetooth-music-wifi-3g-obd2-mirror-link-rearview-camera-video-aux-dvr


This top 2006-2011 Kia sedona car stereo comes with an a large 6.2 inch HD 800*480 multi-touch screen for the better display of videos and view of the navigation. With built-in 3D GPS, this car stereo can provide you with turn-by-turn directions to help you reach the destinations. What’s more, lifetime traffic updates can help you avoid all kinds of traffic situations. You can also easily get access to the multimedia for example DVD, bluetooth music, and radio for fun in the motion. Go with it and have fun from now on! Good luck to you!

Posted in Uncategorized.

How to upgrade a 2009 2010 2011 DODGE RAM Pickup Trucks enger Caliber Challenger Dakota Dura radio with Bluetooth Music Mirror Link OBD2 3G WiFi Video

Getting an ideal car radio, can you install it on your own? If not, it’s suggested you go to a car stereo upgrade center or ask a professional for help. If you have a 2009 2010 2011 DODGE RAM Pickup Trucks enger Caliber Challenger Dakota Dura radio and are going to upgrade your factory radio, you can refer to this professional DODGE RAM Pickup Trucks enger Caliber Challenger Dakota Dura radio installation guide from Seicane at first, which may help a lot for the installation.

2009 2010 2011 DODGE RAM Pickup Trucks enger Caliber Challenger Dakota Dura radio after installation

2009 2010 2011 DODGE RAM Pickup Trucks enger Caliber Challenger Dakota Dura radio after installation

Some tips before the installation:

1.Please disconnect the power before the installation.

2.Please prepare a lever and a screwdriver before the removal and the installation.

3.Please keep all the separate parts from the car. Please take great care of the dashboard to avoid scratching it during its detachment and installation. Please keep handy any parts from the car and make use of all the original screws from the car as much as possible. so each related part of the unit can be fixed securely.

4.For your convenience, here’s the recommended tools for removal and installation from Seicane, please check for more details: http://www.seicane.com/car-dvd-dismantling-device-srd-400

2009 2010 2011 DODGE RAM Pickup Trucks enger Caliber Challenger Dakota Dura radio installation guide

1. The original car radio.

The original car radio

The original car radio

2. Remove the panel by prying the edges with a lever.

Remove the panel by prying the edges with a lever

Remove the panel by prying the edges with a lever

3. Unscrew four screws holding the original radio in place with a screwdriver.

Unscrew four screws holding the original radio in place with a screwdriver

Unscrew four screws holding the original radio in place with a screwdriver

4. Take the original radio out of the dash.

Take the original radio out of the dashTake the original radio out of the dash

Take the original radio out of the dash

5. Disconnect the connectors at the back of the original radio.

Disconnect the connectors at the back of the original radio

Disconnect the connectors at the back of the original radio

6. Check all the accessories for the new Seicane car radio.

Check all the accessories for the new Seicane car radio

Check all the accessories for the new Seicane car radio

7. Connect the harnesses to the back of the new Seicane car radio.

Connect the harnesses to the back of the new Seicane car radio

Connect the harnesses to the back of the new Seicane car radio

8. Connect the Seicane car radio to your original car radio ‘s plugs.

9. Turn on the new Seicane radio to have a careful check if everything works well. If it doesn’t, please check whether all the cables are connected correctly.

10. Put the new Seicane radio into the dash.

11. Put everything into their original place.

Now with the help of this detailed installation guide for a 2009 2010 2011 DODGE RAM Pickup Trucks enger Caliber Challenger Dakota Dura radio, can you install your new radio on your onwn? If not, you can ask a professional to install. If you are still looking for a suitable head unit for your car, I’d like to recommend an amazing DODGE RAM Pickup Trucks enger Caliber Challenger Dakota Dura radio from Seicane to you. Please click for more details:

http://www.seicane.com/seicane-s126061-oem-android-dvd-player-for-2009-2010-2011-dodge-ram-pickup-trucks-enger-caliber-challenger-dakota-dura-radio-replacement-with-touch-screen-gps-car-stereo-bluetooth-music-mirror-link-obd2-3g-wifi-video-backup-camera

If your car is one of the DODGE RAM Pickup Trucks enger Caliber Challenger Dakota Dura of year from 2009, 2010 to 2011, then this in dash DODGE RAM Pickup Trucks enger Caliber Challenger Dakota Dura radio can fit to your factory radio. The built-in navigation system can let you can go anywhere without getting lost. This high quality DVD player will also add a large amount of entertainment for your families and passengers during the tiring and boring long trip. The reverse camera is also supported for parking. Wish you like it and have a wonderful time with it. Good luck!

Posted in Uncategorized.

How to install a 2013 2014 Nissan X-Trail car radio with CD DVD Player 3G WiFi Mirror Link Touch Screen OBD2 Auto A/V USB SD Quad-core CPU

Have you ever installed a new car radio on your own? If not, you may think it quite hard for you to do it. Actually, with a detailed installation guide, it’s easy to remove the factory radio and install a new one. If you are going to upgrade the capabilities of your factory radio, you can find an installation guide to help you. Here comes a step-by-step 2013 2014 Nissan X-Trail car radio installation guide from Seicane, wish you can get some help from it.

2013 2014 Nissan X-Trail car radio after installation

2013 2014 Nissan X-Trail car radio after installation

Before and during installation, you should notice:

1.Before connecting, please make sure the ignition is off to avoid short circuit.

2.Ensure connect the yellow and red power cable at last.

3.Ensure that all loose wires are isolated with electrical tape

4.Ensure don’t tangle the wire when tighten the moving parts(Such as seat rails).

5.Ensure that all ground is connected to the same place.

6.Using the improper fuse may cause damage of fire, so when replace the fuse, please consult the professional.

7.For your convenience, here’s the recommended tools for removal and installation from Seicane, please check for more details: http://www.seicane.com/car-dvd-dismantling-device-srd-400

2013 2014 Nissan X-Trail car radio installation guide

1. Remove the right trim panel with a lever.

Remove the right trim panel with a lever

Remove the right trim panel with a lever

2. Remove the left trim panel with the same way as step 1.

Remove the left trim panel with the same way as step 1

Remove the left trim panel with the same way as step 1

3. Pry the edges of the a/c controller with a lever.

Pry the edges of the air conditioner controller with a lever

Pry the edges of the air conditioner controller with a lever

4. Take the a/c controller out of the dash.

Take the air conditioner  controller out of the dash

Take the air conditioner controller out of the dash

5. Unscrew all the screws holding the original car radio in place with a screwdriver.

Unscrew all the screws holding the original car radio in place with a screwdriver

Unscrew all the screws holding the original car radio in place with a screwdriver

6. Gently take the original car radio out the dash.

7. Disconnect all the connectors at the back of the original car radio.

8. Check all the accessories for the new Seicane car radio.

9. Connect the harnesses to the back of the new Seicane car radio.

10. Connect the Seicane car radio to your original car radio ‘s plugs.

11.Turn on the new Seicane radio to have a careful check if everything works well. If it doesn’t, please check whether all the cables are connected correctly.

12.Put the new Seicane radio into the dash.

13. Put everything into their original place.

With the help of this step-by-step installation instruction, can you install this 2013 2014 Nissan X-Trail car radio in your car? If you find it too hard for you, you’d better turn to a professional for help. Before and during the installation, you can also seek help from your dealer if you encounter any problem. If you don’t find an ideal car radio, you can refer to this wonderful Nissan X-Trail car radio from Seicane. Here’s the link, please click:

http://www.seicane.com/seicane-s128007-8-inch-android-gps-radio-bluetooth-multimedia-navigation-system-for-2013-2014-nissan-x-trail-with-cd-dvd-player-3g-wifi-mirror-link-touch-screen-obd2-steering-wheel-control-auto-a-v-usb-sd-quad-core-cpu-16g-flash-s128007

This intelligent 2013 2014 Nissan X-Trail car radio comes with multiple features like Bluetooth, GPS navi system, USB, iPod connection for accurate guidance to anywhere you want to as well as relaxing and exciting entertainment experience during the driving. And one year warranty is included. Just enjoy your amazing trips with this intelligent 2013 2014 Nissan X-Trail car radio from now on!

Posted in Uncategorized. Tagged with , .

How to replace a 2009-2013 Toyota Prius car radio with Bluetooth Music 3G WiFi Mirror Link OBD2 Rearview Camera Steering Wheel Control AUX DVR USB SD Quad-core CPU

Under the guidance of a detailed installation guide, can you finish the installation of a new head unit on your own? Some of you may say yes if you have similar installation experience before. As a matter of fact, it’s quite easy to install a new aftermarket unit. Here comes a professional installation guide from Seicane which is specific for the installation of a 2009-2013 Toyota Prius car radio. If you also have the same dashboard as the picture below, you can read it carefully as a reference.

2009-2013 Toyota Prius car radio after installation

2009-2013 Toyota Prius car radio after installation

Precautions for this installation:

1.Before you start up any work, park your car well and unplug the negative power cable to avoid any danger.

2.Please make sure that all fastened wires are isolated with electrical tape.

3.Please make sure the ignition is off to avoid short circuit.

4. For your convenience, here’s the recommended tools for removal and installation from Seicane, please check for more details: http://www.seicane.com/car-dvd-dismantling-device-srd-400

2009-2013 Toyota Prius car radio installation guide

1. Remove the shift panel right of the steering wheel. The panel simply pulls free of the dash with medium force from a trim pry tool.

Remove the shift panel right of the steering wheel

Remove the shift panel right of the steering wheel

2. Remove the dash panel below the stereo. Grab the panel by the right edge and pull with significant force to detach the plastic pin that holds the panel in place. Grab the bottom edge of the panel and pull it from the dash.

Remove the dash panel below the stereo

Remove the dash panel below the stereo

3. Remove the vent panel to the right of the stereo as you did the left panel. It is only connected with clips that can be pulled free with moderate force.

Remove the vent panel to the right of the stereo as you did the left panel

Remove the vent panel to the right of the stereo as you did the left panel

4. Disconnect the wiring.

Disconnect the wiring

Disconnect the wiring

5. Remove the stereo by removing the four screws near the corners of the stereo mounting bracket with a Phillips-head screwdriver.

Remove the stereo by removing the four screws near the corners of the stereo mounting bracket with a Phillips-head screwdriver

Remove the stereo by removing the four screws near the corners of the stereo mounting bracket with a Phillips-head screwdriver

6. Pull the radio toward you slowly.

6. Pull the radio toward you slowly

6. Pull the radio toward you slowly

7. Pull the stereo from its dock and pull the wire groups from the back of the stereo. Grab the groups by the white plastic wire binders, not the wires themselves.

Pull the stereo from its dock and pull the wire groups from the back of the stereo

Pull the stereo from its dock and pull the wire groups from the back of the stereo

8. Check all the accessories for the new Seicane car radio.

9. Connect the harnesses to the back of the new Seicane car radio.

10. Connect the Seicane car radio to your original car radio ‘s plugs.

11. Turn on the new Seicane radio to have a careful check if everything works well. If it doesn’t, please check whether all the cables are connected correctly.

12. Put the new Seicane radio into the dash.

13. Put everything into their original place.

That’s all the installation guide for a 2009-2013 Toyota Prius car radio. Wish it can be helpful for you. If you find there is little difference between your dashboard from that shown in the guide, please rest assured, the installation is similar on the whole, you can still refer to this guide to help with the installation.

By the way, do you find an ideal car radio for your car? If not, I’d like to recommend an ideal Toyota Prius car radio from Seicane to you. For more details, you are welcome to check it out with the following link:

http://www.seicane.com/seicane-s128009-8-inch-android-hd-1024-600-touch-screen-radio-gps-car-a-v-system-for-2009-2013-toyota-prius-left-with-dvd-player-bluetooth-music-3g-wifi-mirror-link-obd2-rearview-camera-steering-wheel-control-aux-dvr-usb-sd-quad-core-cpu-s128009

This multifunctional Toyota Prius car radio comes with multiple functions including DVD, GPS Nav, Bluetooth, TV, FM/AM, iPod, RDS, USB and SD etc. With built-in 3D GPS, the precise location directions can be displayed on the 8 inch multi-touch screen to your desired destination, so you will not get lost in a strange place. You are enabled to stream from music and make and receive calls without taking your hands off the steering wheel control when your bluetooth-enabled mobile phone is connected with the bluetooth of this stereo. Why not take it right now and have a wonderful time with it? Good luck to you!

Posted in Uncategorized.

How to easily install a 2012-2013 Skoda RAPID head unit with 8 inch 1024*600 multi-touch screen 8 inch 1024*600 multi-touch screen

If you think your factory radio comes with few features, which can’t meet all your needs in your car. It’s a great ideal for you to upgrade it with a multifunctional head unit which features GPS navigation, FM/AM radio, DVD player, Bluetooth hands-free calls, streaming music, etc. To install a new unit in your car, you can find a professional detailed professional guide to help you. This detailed 2012-2013 Skoda RAPID head unit installation instruction from Seicane is for your reference.

2012-2013 Skoda RAPID head unit after installation

2012-2013 Skoda RAPID head unit after installation

Before and during installation, you should notice:

1.Before connecting, please make sure the ignition is off to avoid short circuit.

2.Ensure connect the yellow and red power cable at last.

3.Ensure that all loose wires are isolated with electrical tape

4.Ensure don’t tangle the wire when tighten the moving parts(Such as seat rails).

5.Ensure that all ground is connected to the same place.

6.Using the improper fuse may cause damage of fire, so when replace the fuse, please consult the professional.

7.For your convenience, here’s the recommended tools for removal and installation from Seicane, please check for more details: http://www.seicane.com/car-dvd-dismantling-device-srd-400

 

2012-2013 Skoda RAPID head unit installation guide

1.Remove the top panel with a lever.

Remove the top panel with a lever

Remove the top panel with a lever

2.Disconnect the connector at the back of the panel.

Disconnect the connector at the back of the panel

Disconnect the connector at the back of the panel

3.Unscrew the screw with a screwdriver.

Unscrew the screw with a screwdriver

Unscrew the screw with a screwdriver

4.Remove the metal sheet on the top with your hands.

Remove the metal sheet on the top with your hands

Remove the metal sheet on the top with your hands

5.Unscrew two screws circled in red shown as follows under the metal sheet.

Unscrew two screws circled in red shown as follows under the metal sheet

Unscrew two screws circled in red shown as follows under the metal sheet

6.Remove the air conditioner vent with your hands.

Remove the air conditioner vent with your hands

Remove the air conditioner vent with your hands

7.Unscrew two screws under the vent with a screwdriver.

Unscrew two screws under the vent with a screwdriver

Unscrew two screws under the vent with a screwdriver

8.Remove the panel on the original car radio.

Remove the panel on the original car radio

Remove the panel on the original car radio

9.Unscrew four screws holding the original car radio with a screwdriver.

Unscrew four screws holding the original car radio with a screwdriver

Unscrew four screws holding the original car radio with a screwdriver

10.Take the original car radio out of the dash.

Take the original car radio out of the dash

Take the original car radio out of the dash

11.Disconnect all the connectors at the back of the original car radio.

Disconnect all the connectors at the back of the original car radio

Disconnect all the connectors at the back of the original car radio

12.Check all the accessories for the new Seicane head unit.

Check all the accessories for the new Seicane car radio

Check all the accessories for the new Seicane car radio

13.Connect the harnesses to the back of the new Seicane head unit.

Connect the harnesses to the back of the new Seicane car radio

Connect the harnesses to the back of the new Seicane car radio

14.Connect the Seicane head unit to your original car radio ‘s plugs.

15.Turn on the new Seicane head unit to have a careful check if everything works well. If it doesn’t, please check whether all the cables are connected correctly.

16.Put the new Seicane head unit into the dash.

17.Put everything into their original place.

 

The step-by-step 2012-2013 Skoda RAPID head unit installation guide is shown as the above. Wish you can get some help from it. If there is any question, you can consult your dealer. However, if you can’t finish it on your own, you’d better ask a professional for help. If you are still looking for an ideal car stereo for your car, you can refer to this amazing 2012-2013 Skoda RAPID head unit from Seicane. Please click for more details:

http://www.seicane.com/seicane-s128405-8-inch-android-dvd-radio-car-navigation-head-unit-for-2008-2013-vw-volkswagen-scirocco-with-3g-wifi-mirror-link-obd2-bluetooth

With this top 2012-2013 Skoda RAPID head unit in your car, you can easily get to your ideal destinations with the help of the guidance of the 3D GPS. Streaming from music and hands-free calls are available via connecting the bluetooth and your mobile phone. What’s more, the USB connectivity offers compatibility with a variety of media, including MP3 players and more. This car GPS stereo is fully worthwhile of the upgrading for your stock radio.

Posted in Uncategorized.

How to replace a 2004-2011 VW Volkswagen PASSAT(MS127/MK6) car radio with 3G WiFi Mirror Link 1024*600 multi-touch screen

Please look at the picture below, it’s a modern 2004-2011 VW Volkswagen PASSAT(MS127/MK6) car radio from Seicane after installation. If you are a car owner of a 2004-2011 VW Volkswagen PASSAT(MS127/MK6) and are going to replace your factory radio, it’s wise of you to choose such a multifunctional car stereo which can bring quite a lot of convenience and enjoyment for you. Here I’d like to introduce the detailed installation instruction about the VW Volkswagen PASSAT(MS127/MK6) car radio. If you also have the same dashboard as below, you can take it as a reference.

2004-2011 VW Volkswagen PASSAT(MS127  MK6) car radio after installation

2004-2011 VW Volkswagen PASSAT(MS127 MK6) car radio after installation

Some tips before the installation:

1.Please disconnect the power before the installation.

2.Please prepare a lever and a screwdriver before the removal and the installation.

3.Please keep all the separate parts from the car. Please take great care of the dashboard to avoid scratching it during its detachment and installation. Please keep handy any parts from the car and make use of all the original screws from the car as much as possible. so each related part of the unit can be fixed securely.

4.For your convenience, here’s the recommended tools for removal and installation from Seicane, please check for more details: http://www.seicane.com/car-dvd-dismantling-device-srd-400

2004-2011 VW Volkswagen PASSAT(MS127/MK6) car radio installation guide

1. Remove the top panel with a lever.

Remove the top panel with a lever

Remove the top panel with a lever

2. Disconnect the connector at the back of the panel.

Disconnect the connector at the back of the panel

Disconnect the connector at the back of the panel

3. Unscrew the screw with a screwdriver.

Unscrew the screw with a screwdriver

Unscrew the screw with a screwdriver

4. Remove the metal sheet on the top with your hands.

Remove the metal sheet on the top with your hands

Remove the metal sheet on the top with your hands

5. Unscrew two screws circled in red shown as follows under the metal sheet.

Unscrew two screws circled in red shown as follows under the metal sheet

Unscrew two screws circled in red shown as follows under the metal sheet

6. Remove the air conditioner vent with your hands.

Remove the air conditioner vent with your hands

Remove the air conditioner vent with your hands

7. Unscrew two screws under the vent with a screwdriver.

Unscrew two screws under the vent with a screwdriver

Unscrew two screws under the vent with a screwdriver

8. Remove the panel on the original car radio.

Remove the panel on the original car radio

Remove the panel on the original car radio

9. Unscrew four screws holding the original car radio with a screwdriver.

Unscrew four screws holding the original car radio with a screwdriver

Unscrew four screws holding the original car radio with a screwdriver

10. Take the original car radio out of the dash.

Take the original car radio out of the dash

Take the original car radio out of the dash

11. Disconnect all the connectors at the back of the original car radio.

Disconnect all the connectors at the back of the original car radio

Disconnect all the connectors at the back of the original car radio

12. Check all the accessories for the new Seicane car radio.

Check all the accessories for the new Seicane car radio

Check all the accessories for the new Seicane car radio

13. Connect the harnesses to the back of the new Seicane car radio.

Connect the harnesses to the back of the new Seicane car radio

Connect the harnesses to the back of the new Seicane car radio

14.Connect the Seicane car radio to your original car radio ‘s plugs.

15.Turn on the new Seicane car radio to have a careful check if everything works well. If it doesn’t, please check whether all the cables are connected correctly.

16.Put the new Seicane car radio into the dash.

17. Put everything into their original place.

Are you able to can you install this 2004-2011 VW Volkswagen PASSAT(MS127/MK6) car radio in your car after reading this step-by-step installation instruction? If you have any question, you can turn to a professional for help. Please make clear all the steps, so that you can achieve the installation easily.

In addition, it’s vital for you to make sure you have a right car stereo for your car. If you have no idea about this, you can refer to this modern VW Volkswagen PASSAT(MS127/MK6) car radio from Seicane. Here’s the link, please click:

http://www.seicane.com/seicane-s128405-8-inch-android-dvd-radio-car-navigation-head-unit-for-2008-2013-vw-volkswagen-scirocco-with-3g-wifi-mirror-link-obd2-bluetooth

This large 8 inch VW Volkswagen PASSAT(MS127/MK6) car radio effortlessly handles the web’s most popular video and audio file formats like DVD/DIVX/MP4/MP3/MP2/VCD with style. Connect your portable media player to this unit through the USB port or better yet, maximize your driving exhilaration with access to your complete music collection by attaching your iPod to it. Bluetooth functionality is available with this car DVD player, which allows you to stream music of your mobile phones and have hands-free conversations with your callers. Take it right now and have a wonderful time on all trips!

Posted in Uncategorized.

How to upgrade a 2008-2013 VW Volkswagen Golf 6(MK6) head unit with Digital TV Car DVR Mirror link OBDII USB SD FM/AM radio 1024*600 multi-touch screen

Please look at the picture below, it’s a 2008-2013 VW Volkswagen Golf 6(MK6) head unit from Seicane after installation. If you own a 2008-2013 VW Volkswagen Golf 6(MK6) and have the same dashboard, then it can fit your car. To enjoy more modern features, it’s wise of you to replace your factory radio with an aftermarket head unit. This passage is a step-by-step installation guide specially for the 2008-2013 VW Volkswagen Golf 6(MK6) head unit, you can read it carefully, which may help you install your new head unit in your car by yourself.

2008-2013 VW Volkswagen Golf 6(MK6) head unit after installation

2008-2013 VW Volkswagen Golf 6(MK6) head unit after installation

Before and during installation, you should notice:

1.Before connecting, please make sure the ignition is off to avoid short circuit.

2.Ensure connect the yellow and red power cable at last.

3.Ensure that all loose wires are isolated with electrical tape

4.Ensure don’t tangle the wire when tighten the moving parts(Such as seat rails).

5.Ensure that all ground is connected to the same place.

6.Using the improper fuse may cause damage of fire, so when replace the fuse, please consult the professional.

7.For your convenience, here’s the recommended tools for removal and installation from Seicane, please check for more details: http://www.seicane.com/car-dvd-dismantling-device-srd-400

2008-2013 VW Volkswagen Golf 6(MK6) head unit installation guide

1. Remove the top panel with a lever.

Remove the top panel with a lever

Remove the top panel with a lever

2. Disconnect the connector at the back of the panel.

Disconnect the connector at the back of the panel

Disconnect the connector at the back of the panel

3.Unscrew the screw with a screwdriver.

Unscrew the screw with a screwdriver

Unscrew the screw with a screwdriver

4. Remove the metal sheet on the top with your hands.

Remove the metal sheet on the top with your hands

Remove the metal sheet on the top with your hands

5. Unscrew two screws circled in red shown as follows under the metal sheet.

Unscrew two screws circled in red shown as follows under the metal sheet

Unscrew two screws circled in red shown as follows under the metal sheet

6. Remove the air conditioner vent with your hands.

Remove the air conditioner vent with your hands

Remove the air conditioner vent with your hands

7. Unscrew two screws under the vent with a screwdriver.

Unscrew two screws under the vent with a screwdriver

Unscrew two screws under the vent with a screwdriver

8. Remove the panel on the original car radio.

Remove the panel on the original car radio

Remove the panel on the original car radio

9. Unscrew four screws holding the original car radio with a screwdriver.

Unscrew four screws holding the original car radio with a screwdriver

Unscrew four screws holding the original car radio with a screwdriver

10. Take the original car radio out of the dash.

Take the original car radio out of the dash

Take the original car radio out of the dash

11. Disconnect all the connectors at the back of the original car radio.

Disconnect all the connectors at the back of the original car radio

Disconnect all the connectors at the back of the original car radio

12. Check all the accessories for the new Seicane head unit.

Check all the accessories for the new Seicane car radio

Check all the accessories for the new Seicane car radio

13. Connect the harnesses to the back of the new Seicane head unit.

Connect the harnesses to the back of the new Seicane car radio

Connect the harnesses to the back of the new Seicane car radio

14. Connect the Seicane head unit to your original car radio ‘s plugs.

15. Turn on the new Seicane head unit to have a careful check if everything works well. If it doesn’t, please check whether all the cables are connected correctly.

16.Put the new Seicane head unit into the dash.

17. Put everything into their original place.

If you find your dashboard is different from that in the guide, please don’t worry, the installation is similar on the whole, and it won’t have much influence, so you still can take it as a reference. If you have any question, you can consult your dealer. But if you still don’t have a suitable unit for your car, I’d like to share an amazing 2008-2013 VW Volkswagen Golf 6(MK6) head unit from Seicane with you. Here’s the link, please click:

http://www.seicane.com/seicane-s128405-8-inch-android-dvd-radio-car-navigation-head-unit-for-2008-2013-vw-volkswagen-scirocco-with-3g-wifi-mirror-link-obd2-bluetooth

This modern 2008-2013 VW Volkswagen Golf 6(MK6) head unit comes with a built-in GPS and advanced features for you to get to the destinations easily and have hands free calls during the driving. What’s more, you can enjoy hands-free calling convenience and music streaming pleasure via the Bluetooth connection all the way. Wish you like it and have a wonderful time with it!

Posted in Uncategorized.

How to install a 2014 Toyota Tundra car radio with DVD AM FM Radio Bluetooth Mirror Link OBD2 Touch Screen 3G WiFi USB SD Auto A/V Quad-core CPU 16G Flash

Some professional knowledge is definitely required in installing a car stereo. However, if you have some related installation experience and a correct installation guide, you can also achieve the installation on your own easily. If you own a 2014 Toyota Tundra , the following 2014 Toyota Tundra car radio installation guide from Seicane can be helpful for you. The picture below is take after the installation for your reference.

2014 Toyota Tundra car radio after installation

2014 Toyota Tundra car radio after installation

Some tips before the installation:

1.Please disconnect the power before the installation.

2.Please prepare a lever and a screwdriver before the removal and the installation.

3.Please keep all the separate parts from the car. Please take great care of the dashboard to avoid scratching it during its detachment and installation. Please keep handy any parts from the car and make use of all the original screws from the car as much as possible. so each related part of the unit can be fixed securely.

4.For your convenience, here’s the recommended tools for removal and installation from Seicane, please check for more details: http://www.seicane.com/car-dvd-dismantling-device-srd-400

 

2014 Toyota Tundra car radio installation guide

1.The original car radio.

The original car radio

The original car radio

2.Pry the panel beneath the air conditioner controller with a lever, then remove it.

2-1. Pry the panel beneath the air conditioner controller with a lever.

2-1. Pry the panel beneath the air conditioner controller with a lever.

2-2. Remove the panel.

2-2. Remove the panel.

3.Remove the air conditioner controller with your hands.

Remove the air conditioner controller with your hands

Remove the air conditioner controller with your hands

4.Unscrew the screws circled in red as follows which hold the original car radio in place with a screwdriver.

Unscrew the screws circled in red as follows which hold the original car radio in place with a screwdriver

Unscrew the screws circled in red as follows which hold the original car radio in place with a screwdriver

5.Gently take the original car radio out of the dashboard.

Gently take the original car radio out of the dashboard

Gently take the original car radio out of the dashboard

6.Disconnect the connectors at the back of the original car radio.

7.Check all the accessories for the new Seicane car radio.

Check all the accessories for the new Seicane car radio

Check all the accessories for the new Seicane car radio

8.Connect the harnesses to the back of the new Seicane car radio.

Connect the harnesses to the back of the new Seicane car radio

Connect the harnesses to the back of the new Seicane car radio

9.Connect the Seicane car radio to your original car radio ‘s plugs.

10.Turn on the new Seicane car radio to have a careful check if everything works well. If it doesn’t, please check whether all the cables are connected correctly.

11.Put the new Seicane car radio into the dash.

12.Put everything into their original place.

 

That’s all the installation guide for a 2014 Toyota Tundra car radio. Can you understand all the steps? If not, you can consult your dealer. Please make sure you are clear about every step before you start your installation. If you don’t have an ideal radio for your car, I’d like to recommend a great 2014 Toyota Tundra car radio from Seicane to you. Here’s the link, please click:

http://www.seicane.com/seicane-s128004-8-inch-android-gps-sat-nav-car-stereo-for-2014-toyota-tundra-with-dvd-am-fm-radio-bluetooth-mirror-link-obd2-touch-screen-3g-wifi-usb-sd-steering-wheel-control-auto-a-v-quad-core-cpu-16g-flash-s128004

With convenient, practical and humanizing operation interface, this amazing 2014 Toyota Tundra car radio has voice prompts for accurate guidance and re-planning of the route automatically, leading you smoothly all the way. It can also provides great quality music streaming, hands-free calls via Bluetooth technology and iPod function is supported, too. Just take it on your way to have fun. Good luck to you!

Posted in Uncategorized.