http://www.carstereofaqs.com/wp-admin/edit.php?post_type=custom-css-js

Monthly Archives: September 2015

How to remove and install 2009-2013 Toyota Sienna Radio navigation system with IPOD aux

The Toyota Sienna is a family minivan first produced by Toyota in 1998 and renowned for high reliability; it is still in production as of now. The Toyota Sienna can develop chronic radio problems, however, we can remove it and install a new aftermarket Toyota Sienna Radio to aviod these problems.Look at this image below, if your car have the same dashboard with it. There are some instructions of how to install a new radio.

2009-2013 Toyota Sienna dashboard

2009-2013 Toyota Sienna dashboard

2009-2013 Toyota Sienna radio removal

(1)Open the instrument box. See where the hands are. Just pull that brown panel out in the middle first.

2009-2013 Toyota Sienna Radio removal step 1

2009-2013 Toyota Sienna Radio removal step 1

(2) Now carefully pull it on both sides.

2009-2013 Toyota Sienna Radio removal step 2

2009-2013 Toyota Sienna Radio removal step 2

(3) When it is in your hands disconnect the harness.

2009-2013 Toyota Sienna Radio removal step 3

2009-2013 Toyota Sienna Radio removal step 3

(4) See where the hands are. Pull the panel around the gear switcher.

2009-2013 Toyota Sienna Radio removal step 4

2009-2013 Toyota Sienna Radio removal step 4

(5) To take it out you will need to remove the gear switcher handle.

2009-2013 Toyota Sienna Radio removal step 5

2009-2013 Toyota Sienna Radio removal step 5

(6) Twist it counter-clockwise. Use power of your hands to start the move.

2009-2013 Toyota Sienna Radio removal step 6

2009-2013 Toyota Sienna Radio removal step 6

(7) See where the hands are. Pull it to remove the A/C controls panel.

2009-2013 Toyota Sienna Radio removal step 7

2009-2013 Toyota Sienna Radio removal step 7

(8) we will need a wrench to remove 4 bolts. Actually I used magnet tool also. That way it is easier not to drop them somewhere inside.

2009-2013 Toyota Sienna Radio removal step 8

2009-2013 Toyota Sienna Radio removal step 8

(9) See where the hands are. Pull the radio and air registers out.

2009-2013 Toyota Sienna Radio removal step 9

2009-2013 Toyota Sienna Radio removal step 9

(10) And here we go. It is in hands.

2009-2013 Toyota Sienna Radio removal step 10

2009-2013 Toyota Sienna Radio removal step 10

With these steps above, we can remove the Toyota Sienna Radio easily. After few minutes rest, we can install the new radio immediately.

2009-2013 Toyota Sienna radio installation

(1) Make antennas and cables connected step by step as installation instructions show,and you should be very careful when you are doing this for it will affect whole procedure.

(2) Connected the new radio to your Toyota Sienna, you should check whether your connections are correct, the new unit is in right position,and you’d better have a tidy for the cables.

(3)Firm four removed screws that are put aside,then make trim panel back on your new unit

 

Arrangement for wiring must be reasonable during your installation process. Usually, the space for installation is limited. You’d better reduce unnecessary wirings’ space to make the dvd gps easier to install and function.The cables and wires of car and new radio must be routed properly to avoid touching any moving parts,include steering wheel column acceleration pedal and brake pedal. All antennas must be bonded properly to against any loose during driving.

 

By the way, if you don’t know which unit is better. I’d like to introduce a good one to you:

http://www.seicane.com/seicane-s128006-quad-core-android-4-4-4-2009-2013-toyota-sienna-aftermarket-car-stereo-radio-dvd-gps-navigation-system-with-3g-wifi-bluetooth-music-mirror-link-obd2-usb-sd-1024-600-multi-touch-capacitive-screen-hd-1080p-video-steering-wheel

This unit has Quad-core Android 4.4.4 operation system and 8 inch HD 1024*600 multi-touch screen with smooth operation, you can use high speed 3G&WiFi internet. You can download any applications in the android market for access to games, Skype, MSN, YouTube and so on. You can also use 3D navigation maps. Isn’t it awesome?

 

Wish you can learn something from this blog, have fun with your Toyota Sienna Radio every day.

Posted in Toyota car DVD. Tagged with .

How to remove and install 2005 2006-2010 Skoda OCTAVIA II Radio

Nowadays, 2005-2010 Skoda OCTAVIA II is a good choice for us.Some of you might be owners of 2005-2010 Skoda OCTAVIA II. But you may have no idea how to remove and install Skoda OCTAVIA II radio. Skoda OCTAVIA II is pretty good, if you have a new aftermarket radio can make your drive more convenience and comfortable.And here is the dashboard of 2005-2010 Skoda OCTAVIA II.

Skoda OCTAVIA II dashboard

Skoda OCTAVIA II dashboard

By the way, if you didn’t have a new aftermarket radio yet. I’d like to share a good one with you.

http://www.seicane.com/android-2005-2010-skoda-octavia-ii-radio-bluetooth-dvd-player-navigation-system-with-mirror-link-hd-capacitive-multi-touch-screen-obd-dvr-bluetooth-rear-view-camera-tv-3g-wifi-ipod-s168032

This aftermarket radio has High quality RK3188 1.6 GHz Cortex A9 Quad-core processor with 1GB Samsung DDR3. And 8 inch HD 1024*600 multi-touch screen with smooth operation, high sensitivity and abundant interaction for the better view of your road ahead. The most attractive is it’s intelligent pure android 4.4.4 operation system with exquisite and user-friendly user interface. You can set any of your favorite application icons as shortcut on the main menu and set the position of the icons according to your preference.

Do you think this unit fits your Skoda OCTAVIA perfect? Let’s remove the factory radio now.

2005-2010 Skoda OCTAVIA II radio removal

1) Pry up the panel around the original Skoda OCTAVIA II radio with crowbars

Skoda OCTAVIA II Radio removal step 1

Skoda OCTAVIA II Radio removal step 1

2) Pick up the panel on the original car radio

Skoda OCTAVIA II Radio removal step 2

Skoda OCTAVIA II Radio removal step 2

3) Remove the four screws around the radio with a screwdriver

Skoda OCTAVIA II Radio removal step 3

Skoda OCTAVIA II Radio removal step 3

4) Pull out the original radio

Skoda OCTAVIA II Radio removal step 4

Skoda OCTAVIA II Radio removal step 4

5) Disconnect the radio antenna in the back of the radio

Skoda OCTAVIA II Radio removal step 5

Skoda OCTAVIA II Radio removal step 5

6) Unplug the electrical plugs running to the back of the radio

Skoda OCTAVIA II Radio removal step 6

Skoda OCTAVIA II Radio removal step 6

The original Skoda OCTAVIA II radio has been removed. After a few munites rest, we can start install a new aftermarket radio next.

2005-2010 Skoda OCTAVIA II radio pre-installation

1)Before connecting,please make sure the ignition is off to avoid short circuit.

2)Ensure connect the yellow and red power cable at last.

3)Ensure that all loose wires are isolated with electricaltape

4)Ensure don’tangle the wire when tighten the moving parts(Such as seat rails).

5)Ensure that all GND is connected to the same place.

6)Using the improper fuse may cause damage of fire,so when replace the fuse,please consult the professional.

2005-2010 Skoda OCTAVIA II radio installation

1)Make antennas and cables connected step by step as installation instructions show,and you should be very careful when you are doing this for it will affect whole procedure.

2)Connected the new aftermarket radio to your Skoda OCTAVIA II, you should check whether your connections are correct, the new unit is in right position,and you’d better have a tidy for the cables.

3)Finally, you can turn on your new aftermarket radio. If it works with no problem, and then you can fix four screws on your new aftermarket radio.Finally put trim panel on the surface of your new Skoda OCTAVIA II radio.

This is the instructions of 2005-2010 Skoda OCTAVIA II radio installation.Is it very easy? But if you still can’t do these steps by yourself, you’d better ask someone professional to help you. Here is a image of after installation.

Skoda OCTAVIA II Radio after installation

Skoda OCTAVIA II Radio after installation

Wish you can have a good time with your Skoda OCTAVIA II via upgrade the original radio.

Posted in Uncategorized. Tagged with .

How to replace remove install 2007-2010 Ford Mondeo radio

Some of you might be the owners of Ford Mondeo(2007-2010).And you want to remove and install or replace your factory radio to aftermarket radio.But the problem is you have no idea how to remove your Ford Mondeo radio or install the aftermarket radio. So you can only use car radio which was already outdated.It’s so terrible.By the way,today I will tell you how to replace a 2007-2010 Ford Mondeo radio.

Here is the picture for car radio after installaion,dvd gps navigation system of 2007-2010 Ford Mondeo.

2007-2010 Ford Mondeo radio after installation

2007-2010 Ford Mondeo radio after installation

We can remove the factory radio now.

Remove 2007-2010 Ford Mondeo radio

1)Use a lever to pry downer small trim panel and remove it,then same to right side one.

2007-2010 Ford Mondeo radio remove step 1

2007-2010 Ford Mondeo radio remove step 1

2) After removing a few screws with a screwdriver can pull up the top panel.

2007-2010 Ford Mondeo radio remove step 2

2007-2010 Ford Mondeo radio remove step 2

3) With a lever to pry downer and pull out the panel below.

2007-2010 Ford Mondeo radio remove step 3

2007-2010 Ford Mondeo radio remove step 3

4)Remove few screws below the dash board with a screwdriver.

2007-2010 Ford Mondeo radio remove step 4

2007-2010 Ford Mondeo radio remove step 4

5)Then the panel is taken out.

2007-2010 Ford Mondeo radio remove step 5

2007-2010 Ford Mondeo radio remove step 5

6) Remove four screws to remove the factory radio and unplug connectors.

2007-2010 Ford Mondeo radio remove step 6

2007-2010 Ford Mondeo radio remove step 6

Now factory radio is taken out and next step for you is to install new 2007-2010 Ford Mondeo radio.If you haven’t get aftermarket radio before.Or you have no idea which aftermarket radio is suitable for your Ford Mondeo.I’d like share a good aftermarket radio with you:http://www.seicane.com/hot-selling-android-car-dvd-player-for-2007-2010-ford-mondeo-with-radio-gps-navigation-system-hd-touch-screen-obd-dvr-usb-sd-bluetooth-rear-view-camera-tv-3g-wifi-mirror-link-ipod-s167017

This unit has High quality RK3188 1.6 GHz Cortex A9 Quad-core processor with Andriod 4.4 operation system.And it has many useful functions such as 3G&WiFi,App download,3D navigation and so on.

With a new aftermarket radio,we can start to install it into your Ford Mondeo.

Install 2007-2010 Ford Mondeo radio 

First,you should make sure the brake wire earthed ancd close the parental channel function or change grade setting.

1)Put the new aftermarket radio into the dashboard.

2) Mounted on four screws to fix the new radio.

3)Put on the panel make it fit the new radio.

4) Reconnect the car negative battery terminal.

With several steps above,you can enjoy the entertainment with your new Ford Mondeo radio.You can watch HD 1080P movies with your family or friends on your car. When you come to a city you’ve never been,you can use the 3D navigation to find the right way.And you can surfing internet via 3G or WiFi when you are waiting for someone.

Wish the essay can benefit you,and you can enjoy your car life with a best aftermarket radio.

Posted in Ford car DVD. Tagged with .